+869173158689

Analysis on the die forging process of titanium rods!

Jan 13, 2022

Titanium rod manufacturers analyze the die forging process of titanium rods. The high pressure reduces the life of the titanium rod. Therefore, when the closed die forging method is used to die to forge the titanium rod, the closed die forging must strictly limit the volume of the original blank, which complicates the material preparation process.


Whether to use closed die forging or not should be considered in terms of interest and process feasibility. During open die forging, the burr loss accounts for 15%-20% of the weight of the blank. The technological waste of the clamping part (if necessary to keep this part according to the die forging conditions) accounts for 10% of the weight of the blank. The relative loss of burr metal is usually with the blank The weight decreases and increases. Some forgings with asymmetrical structure, large cross-sectional area difference, and difficult-to-fill local forgings. The burr consumption can be as high as 50%. Multiple transitional grooves will undoubtedly increase auxiliary costs.


Afterward, only the final blank of heat treatment and machining is carried out. The forging temperature and the degree of deformation are the basic factors that determine the structure and performance of the alloy. The heat treatment of titanium rods is different from the heat treatment of steel. Die forging is usually used to make the shape and size close to scrapping. It has no decisive effect on the structure of the alloy. Therefore, the process specification of the final step of the titanium rod plays a particularly important role. It is necessary that the overall deformation of the blank is not less than 30% and the deformation temperature does not exceed the phase transition temperature. In order to obtain the high strength and plasticity of the titanium rod at the same time, the temperature and deformation degree must be distributed as evenly as possible in the entire deformed blank.


After recrystallization and heat treatment, the uniformity of titanium rods and performance is not as good as that of steel forgings. The metal fierce flow zone has fuzzy crystals at low magnification and fine equiaxed crystals at high magnification; in the difficult-to-deform area, due to the small amount of deformation or no deformation, the structure is often kept in the state before deformation. Therefore, when die forging some important titanium rod parts (such as compressor disks, blades, etc.), in addition to controlling the deformation temperature below TB and an appropriate deformation level, it is very important to control the structure of the original blank. Otherwise, the coarse-grained structure or Certain defects will be inherited into the forgings, and the subsequent heat treatment cannot be eliminated, which will cause the forgings to be scrapped.


In the sharp deformation area where the thermal effect is locally concentrated when forging a titanium rod forging with a complex shape on the hammer. Even if the heating temperature is strictly controlled, the temperature of the metal may still exceed the TB of the alloy. For example, when the titanium rod blank with an I-shaped cross-section is die-forged, the hammer is too heavy, and the local temperature in the middle (web area) is affected by the thermal effect of deformation. The edge is locally high about 100°C. In addition, the difficult-to-deform area and the area with critical deformation level are easy to form coarse-grained structures with relatively low plasticity and durable strength during the healing process after die forging. Therefore, the mechanical properties of forgings with complex shapes on the hammer are often unstable. But it will lead to a sharp increase in deformation resistance, although reducing the heating temperature of die forging can eliminate the risk of local overheating of the blank. To increase tool wear and power consumption, it is also necessary to use more powerful equipment.


The multiple tapping method can also reduce local overheating of the blank. However, it is necessary to increase the heating frequency, when the hammer is forged. To make up for the heat lost by the contact between the blank and the colder mold. And when the requirements for the plasticity and durability strength of the deformed metal are not too high, forgings with relatively simple shapes are die-forged. It is better to use hammer forging. But the beta alloy is not suitable for hammer forging, because multiple heating during the die forging process will have a beneficial effect on the mechanical properties. Compared with the forging hammer, the working speed of the press (hydraulic press, etc.) is greatly reduced, which can reduce the deformation resistance and deformation heat effect of the alloy. When the titanium rod is die-forged on the hydraulic press, the unit dies forging force of the blank is about 30% lower than that of the hammer die forging, which can increase the life of the die. The reduction of thermal effect also reduces the risk of metal overheating and temperature rise exceeding TB.


When the unit pressure is used for forging with a press under the same conditions as forging with a forging hammer. The heating temperature of the blank can be reduced by 50100℃. In this way, the interaction between the heated metal and the periodic gas and the temperature difference between the blank and the mold is correspondingly reduced, thereby improving the uniformity of deformation, the uniformity of the structure of the die forging is also greatly improved, and the consistency of mechanical properties is also improved. . Reduce the deformation speed, the area shrinkage rate with the most obvious numerical increase, and the area shrinkage rate is the most sensitive to the structural defects caused by overheating.


The friction with the tool is large and the surface of the blank cools too fast in contact. In order to improve the fluidity of the titanium rod and increase the life of the mold. The usual approach is to increase the forging angle and fillet radius and use lubricants: the height of the burr bridge on the forging die is larger than that of steel, and the deformation of the titanium rod is characterized by being more difficult to flow into the deep and narrow die groove than steel. This is because the deformation resistance of titanium is high. Generally about 2mm larger. Sometimes a burr groove with a non-uniform bridge size can be used to restrict or accelerate the flow of metal to a certain part of the groove. For example, in order to make the groove easy to fill. A rectangular box-shaped forging (as shown in Figure 12) has thin front and rear sidewalls; left and right side walls are thicker. When the burr groove shown in B-B is used around the box-shaped member, the metal has small resistance to flowing into the left and right side walls, which makes it difficult for the metal to flow to the thin front and rear sidewalls, and the filling is not full. Later, the front and rear sidewalls still use burr grooves shown in BB, while the left and right side walls are replaced with burr grooves shown in AA. Due to the wide bridge size and the obstruction of the damping groove, the front and rear thinner side walls are completely filled, and the metal is relatively thin. Use the aforementioned burr groove method to save money.


It provides a feasible method for solving the forming of large and complex titanium rod precision forgings. This method has been widely used in the production of titanium rods. One of the most effective ways to improve the fluidity of titanium rods and reduce the deformation resistance is to increase the preheating temperature of the mold. Isothermal die forging and hot die forging developed in the past two to three decades at home and abroad.


Please send an email to sales1@bjjfti.com if need, or submit your requirements at the bottom, we will reply to you within 12 hours!  
Send Inquiry