Application of Corrosion Resistant Titanium Alloy on Ships
Titanium alloys are widely used in various fields because of their high strength, good corrosion resistance, and high heat resistance. Many countries in the world have recognized the importance of titanium alloy materials, and have successively carried out research and development on them, and have been put into practical applications. Titanium alloys have great development potential in ship applications. The following describes the application of titanium alloys on ships:


1. Application in ship structure.
Although titanium and titanium alloys have high yield strength, they require inert gas protection during welding, which is more difficult to form than steel. Therefore, titanium is rarely used in general surface ship structures. Titanium and titanium alloys are mainly used in submarines, submersibles and other ships to cope with occasions that require high yield strength, density and corrosion resistance at the same time.
my country developed Ti80 alloy in the 1980s, which is used to manufacture the pressure-resistant shells of deep submersibles and submarines. It has excellent properties such as high strength, high toughness, corrosion resistance, and weldability. Under the condition of yield strength of 785~885MPa, the fracture toughness and stress corrosion resistance are obviously better than those of Ti6Al4VELI alloy. The Ti91 titanium alloy developed in the 1990s has a yield strength of 700MPa.
2. Used for ship coolers.
Since titanium and titanium alloys have better corrosion resistance than other alloys in seawater, and have high strength and low density compared with commonly used copper alloys, the heat transfer efficiency can be ensured by reducing the thickness of the tube wall and increasing the flow rate of seawater. In the fields of nuclear submarines and other applications that have high requirements on the safe operation and reliability of equipment, the application of titanium heat exchangers is very important.
At present, the most widely used industrial pure titanium in the United States is industrial pure titanium, which has special stress corrosion resistance in natural water, seawater and various chlorides. In desalination equipment with seawater flow rate of 3-5m/s, the fouling coefficient of titanium heat exchanger is only 0.95-0.99. my country has also successfully developed some titanium alloys with excellent properties, such as Ti31 titanium alloys, which are used for waste heat discharge coolers, pipelines, etc. The working environment is high-temperature seawater or normal-temperature high-speed seawater, and it is resistant to high temperature corrosion at 180 °C.

3. It is used for ship pipelines.
Due to the direct contact with seawater and most of them are arranged in the bilge, the pipeline of the ship's sea-passing system is in harsh working environment. Corrosion has always been a prominent problem that restricts its maximum performance. In the 1970s, my country successfully developed TA5α titanium alloy (Ti-4Al-0.05B), which has high strength, and the yield strength of as-cast ZTiAl4 is not less than 490MPa, which can be used in the manufacture of pumps and valves in ship auxiliary systems. The Ti75 titanium alloy developed in the 1980s, under the premise of good comprehensive properties, has a strength increase of 50MPa, impact toughness and fracture toughness are 1.4 times and 1.2 times that of TA5, respectively, stress corrosion fracture toughness is 2 times that of TA5, and has excellent Excellent cold and hot workability, casting properties and low impurity sensitivity. Ti75 titanium alloy fills the blank of domestic 730MPa marine titanium alloy and reaches the international advanced level. The reciprocating brine pump made of Ti75 alloy and the valve stem of the side double seat double ball valve have been used normally.
Fourth, for ship propellers.
Titanium alloy has high strength, light weight, excellent resistance to cavitation erosion and fatigue resistance, and is an ideal material for manufacturing propellers. The life of the propeller made of ZTi6Al4V is 3 times that of the copper alloy propeller. my country started the research on ZTi6Al4V alloy in the late 1960s, and successfully applied it to hydrofoil propellers in the 1970s. After 20 years of real boat verification, the performance is good.
In addition, the high-strength cast titanium alloy with better welding performance, higher toughness and better anti-cavitation erosion performance developed in my country has been successful and has been used in the manufacture of a hydrofoil speedboat propeller.






