Industrial Titanium Bar

Product description: The difference from chemically pure titanium is that industrial pure titanium contains a large amount of oxygen, nitrogen, carbon and various other impurity elements (such as iron, silicon, etc.), which is essentially a titanium alloy with low alloy content. Compared with chemically pure titanium, its strength is greatly improved due to the inclusion of more impurity elements, and its mechanical and chemical properties are similar to those of stainless steel (but still lower in strength compared to titanium alloys).

The characteristics of industrial pure titanium bars are:

 low strength, but good plasticity, easy processing, stamping, welding, and good machinability; in the atmosphere, seawater, wet chlorine and oxidizing, neutral, weakly reducing media Good corrosion resistance and oxidation resistance are better than most austenitic stainless steels; but the heat resistance is poor, and the operating temperature should not be too high.

Industrial pure titanium bar is mainly used for working temperature below 350 ℃, with little stress, but requires good plastic stamping parts and corrosion-resistant structural parts, such as: aircraft skeleton, skin, engine accessories; seawater corrosion-resistant pipes for ships, Valves, pumps and hydrofoils, parts of seawater desalination systems; chemical heat exchangers, pump bodies, distillation towers, coolers, agitators, tees, impellers, fasteners, ion pumps, compressor valves and diesel Engine pistons, connecting rods, leaf springs, etc.

American label: GR1, GR2, GR3, GR5, GR7, GR12

American Standard: ASTM B348, ASTM F136, ASTM F67, AMS4928

1: The diameter or side length of the hot-worked bar and its allowable deviation shall meet the requirements of Table 1.

2: After hot processing, the bar is turned (ground) and cold-rolled, and the allowable deviation of the diameter of the cold-drawn bar should meet the requirements of Table 2.

3: The out-of-roundness of the bar that has been turned (ground) after hot processing should not be greater than half of its dimensional tolerance.

4: The indefinite length of the processed bar is 300-6000mm, and the indefinite length of the annealed bar is 300-2000mm. The fixed or double length should be within the range of the indefinite length. The allowable deviation of the fixed length is +20mm ; The length of the double ruler should also be included in the incision amount of the bar, and the amount of each incision is 5mm. The length of the fixed length or the double ruler should be indicated in the contract.

Industrial titanium bar

1. Product description: The difference from chemically pure titanium is that industrial pure titanium contains a large amount of oxygen, nitrogen, carbon and various other impurity elements (such as iron, silicon, etc.), which is essentially a titanium alloy with low alloy content. Compared with chemically pure titanium, its strength is greatly improved due to the inclusion of more impurity elements, and its mechanical and chemical properties are similar to those of stainless steel (but still lower in strength compared to titanium alloys).

2. The characteristics of industrial pure titanium bars are:

 low strength, but good plasticity, easy processing, stamping, welding, and good machinability; in the atmosphere, seawater, wet chlorine and oxidizing, neutral, weakly reducing media Good corrosion resistance and oxidation resistance are better than most austenitic stainless steels; but the heat resistance is poor, and the operating temperature should not be too high.

3. Industrial pure titanium is mainly used for working temperature below 350 ℃, with little stress, but requires good plastic stamping parts and corrosion-resistant structural parts, such as: aircraft skeleton, skin, engine accessories; seawater corrosion-resistant pipes for ships, Valves, pumps and hydrofoils, parts of seawater desalination systems; chemical heat exchangers, pump bodies, distillation towers, coolers, agitators, tees, impellers, fasteners, ion pumps, compressor valves and diesel Engine pistons, connecting rods, leaf springs, etc.

American label: GR1, GR2, GR3, GR5, GR7, GR12

American Standard: ASTM B348, ASTM F136, ASTM F67, AMS4928

1: The diameter or side length of the hot-worked bar and its allowable deviation shall meet the requirements of Table 1.

2: After hot processing, the bar is turned (ground) and cold-rolled, and the allowable deviation of the diameter of the cold-drawn bar should meet the requirements of Table 2.

3: The out-of-roundness of the bar that has been turned (ground) after hot processing should not be greater than half of its dimensional tolerance.

4: The indefinite length of the processed bar is 300-6000mm, and the indefinite length of the annealed bar is 300-2000mm. The fixed or double length should be within the range of the indefinite length. The allowable deviation of the fixed length is +20mm ; The length of the double ruler should also be included in the incision amount of the bar, and the amount of each incision is 5mm. The length of the fixed length or the double ruler should be indicated in the contract.

7. Packaging, shipping,delivery and services

DHL airfreight & by sea transport according to cargo quantities

All Chinese seaports (preferable  Shanghai)

1. How can we know the quality system of your titanium bar ?

Firstly,we can send you a samples for your test, Secondly, We will take all products fully inspected before shipping and finally we have signed international trade insurance , your payment will be 100% refund if any quality problems occurred.

2. Are you a trader or manufacturer?

We are specialized in titanium production and trading more than 12 years, welcome to visit our company anytime when you are convenient.

3. How long to take for delivery?

Case varied,depends on how complex the products you ordered and the quantities,but normally 5-7 days.

4. Can we pay after receive the products?

Normally not,we prefer T/T terms at the beginning, but after we have had  good cooperation then we would like to take your requirement into our consideration.

JFTI has production plant and finished product material warehouse are about 6000 square meters, with more than 10 sets of professional imported processing equipment, including 4500 ton and 1600 ton fast forging unit equipment, cold and hot finishing mill, finishing forging machine, coil leveling machine, cylindrical grinder, seven roll straightener, industrial electric furnace, annealing furnace, etc. At present, the company has R & D department, technology department, production department, sales department, foreign trade department, quality inspection department, etc. There are 10 professional technicians and more than 30 production workers.

Hot Tags: industrial titanium bar, China, suppliers, manufacturers, factory, customized, wholesale, low price, for sale, in stock, hot sale, made in China