+869173158689

Some parts of the car can be made of titanium alloy

Dec 31, 2021

Automotive structural parts that can be made of titanium alloy are mainly engine system valves, springs, and their bearings, connecting rods, crankshafts, gearboxes, steering racks, and pinions, etc., chassis system springs, mufflers, exhaust devices, etc. Body system wheel bushings and bearings, various axle shafts, fasteners, etc. Racing parts have been made of titanium in large quantities because racing cars are cost-free and in the pursuit of victory and safety.

 

The development history of automotive titanium

 

The application of titanium materials in automobiles began in the mid-1950s. In 1956, General Motors Corporation of the United States launched a titanium body exhibition vehicle named "Firebird II". Japan's Nissan Motor Company used some titanium alloy parts in the R382 produced in the late 1960s; Honda Motor Company used titanium to manufacture racing parts in the 1980s.

 

Since the 1990s, some low-cost titanium alloys have been developed due to technological progress, such as Time-62S, Ti metal-LCB, Ti metal-1100, and SP-700 from American Titanium Metals. At the same time, due to the urgency of energy-saving and emission reduction, The requirements for improving performance are increasing, and people's interest in the application of titanium in automobiles has further increased. Japanese-made titanium body and engine cars were exhibited at the 29th International Automobile Exhibition held in Tokyo in 1992; in 1996, the titanium exhaust system developed by Timet was exhibited at the National Association meeting. , And then Chrysler Automobiles manufactured a titanium alloy exhaust system. From 1989 to 1998, 669t of titanium was used in Japanese automobiles. Titanium has also built a factory specializing in the production of automotive titanium alloy parts.

 

Using titanium alloy to manufacture automobile valves can not only reduce the quality, extend the service life, but also improve reliability and save fuel. Early use of titanium alloy with high manufacturing cost, and then use of γ-Ti-Al alloy, the engine's Max speed increased by about 10%. In recent years, some titanium producers have developed a batch of lower-priced titanium alloys for engine valves, and some of them have entered the mass production stage. Improving the wear resistance of titanium alloys for valves is a key technology. Oxygen permeation treatment on the surface, even if there is as much oxygen as possible in the titanium solid solution, is one of the effective processes to improve the surface hardness and wear resistance.

 

The intake and exhaust valves of the V-8 cylinder block manufactured by Del West (Del West) in the United States have been widely used. The intake valve is Ti-6Al-4V, and the exhaust valve is Ti -6Al-2Sn-4Zr-2Mo alloy. The weight of each valve is about 50g lighter than stainless steel, and the service life is extended by 2 to 3 times. The Ti-5Al-2Cr-1Fe alloy intake valve prepared by Hitachi, Japan by the sintering method has been widely used. The R382 and R380 racing cars of Nissan Motor Co. equipped with this intake valve have won many competitions. The winning results. The steel valve used in the past has a weight of 90g, while the titanium alloy valve is only 55g, which is about 40% lighter, and performance improved by 10% to 15%.

 

In 1998, Toyota Motor Corporation’s two-door convertible car and Honda Motor Corporation’s Aliza

(Altezza) All cars use powder metallurgy Ti-6Al-4V/TiB alloy intake valves, and exhaust valves use heat-resistant Ti-Al-Sn-Zr-Mo-Nb-Si/TiB alloys. The former has an engine displacement of 2000ml and is equipped with one 27g intake valve and eight 24g exhaust valves. A total of 408g titanium is used for a car. The valve spring of this car is also made of titanium alloy. It's quality From 43g to 36g, a decrease of 16.3%.

 

The exhaust valve has a high working temperature and can be made of high-temperature titanium alloy Ti-6Al-2Sn-4Zr-2Mo-0.1Si (6242S) alloy. But motorcycle valves are more likely to be exposed to high-temperature areas for a longer time, so the more heat-resistant Ti metal-1100 (Ti-2.7Sn-4Zr-0.4Mo-0.45Si) alloy should be used, which is the titanium alloy with the best heat resistance. One, the working temperature is about 600°C, and the exhaust valve of two-wheeled motorcycles is best made of titanium alloy that can work at 800°C for a long time. At the same time, the alloy should have high damage tolerance performance, so researchers hope to develop a new type of AlTi3 and AITi-based intermetallic compound titanium alloy and have achieved certain results. A representative alloy is: Ti-14Al-21Nb , Ti-14Al-21Nb-3V-2Mo, Ti-24Al-10Nb, Ti-25Al-8Nb-2Mo-2Ta, Ti-25Al-10Nb-3V-1Mo and Ti-22AI-27Nb, but they are expensive .

 

The 746kW V-16 engine of the Cadillac 16 of General Motors Corporation of the United States widely uses light metal materials. The cylinder block and cylinder head are made of aluminum alloy, and the valve spring and some accessories are made of titanium alloy. Its fuel economy reaches 7.23km/L.


Please send an email to sales1@bjjfti.com if need, or submit your requirements at the bottom, we will reply to you within 12 hours! 
Send Inquiry